Systea S.p.A.

Analytical Technologies

Displaying items by tag: reagents
Thursday, 17 March 2022 10:50

μMac-Smart - Portable Analyzer

Portable water analyzer for fast and accurate on-site analysis

µMAC-Smart is a portable analyzer fully controlled by an integrated PC with integrated colour Touch Screen, specifically designed for at site monitoring of all water resources.

µMAC-Smart is robust and reliable: the analyzer is mounted in a compact and easy-to-transport plastic case including room for reagents and all other accessories. A reagent frame holds all reagent bottles and required solutions.

The analyzer is easy to be installed and it is designed for easy operations, the analyzer can be used at site after a quick training. It is delivered from factory fully tested and ready to use reagent kits are available for all standard measurements. Results are stored inside the analyzer memory and can be downloaded through the USB port .Analyzer start up and operations have never been easier! Just turn on and insert the reagents: a simple software will guide the operator through all necessary steps.

Automated calibration 

The analyzer calibration is fully automated; just use the calibration solution as specified in the manual and run. The new calibration factor is checked and accepted if verified to be comprised within acceptance limits.

Multiple parameters
The analyzer can be delivered ready for multiple measurements (MP versions) on the same sample; several multiparametric configurations are available as standard (see here below).
Multiple measurements 
The analyzer offers the option for continuous operational mode; the operator can perform sequential measurements several times on the same sample or just leave the analyzer running while the water sample flows.
Off-scale reanalysis 
The analyzer identifies off scale samples and reanalyze the water sample after automated dilution.

µMAC-Smart standard multiparametric versions

  • MP4 Nutrients: ammonia (fluorimetric OPA), Nitrate+Nitrite, Nitrite and Orthophosphate (colorimetric);
  • Total Nitrogen (UV digestion + 220 nm NO3 direct reading method), eventually coupled with ammonia (colorimetric method);
  • Total Phosphorus (UV+ acidic digestion+ PO4 colorimetric method), eventually coupled with ammonia (colorimetric or fluorimetric method);
  • Total Phosphorus + Total Nitrogen (UV digestion+NO3 UV reduction+ NO2 colorimetric method)
  • ECO version: COD/TOC (UV254 nm direct reading method), coupled with BOD (fluorimetric method) and TSS (nephelometric method).




Published in Portable Analyzers
Thursday, 01 April 2010 10:04

Micromac 1000

On-line and portable analyzer for chemical parameters monitoring in water

µMAC-1000 is an on-line portable analyzer, available either in mono or sequential mutiparametric configuration (µMAC-1000 MP), providing the highest level of analytical automation.

µMAC-1000 is the only high sensitivity multiparametric portable analyzer in the market; it uses the well known wet chemistry methods normally used in the laboratories. The analyzer can measure any type of water samples; a wide range of applications is available, including high sensitivity methods for nutrients analysis in seawater.

Easy to use  Sample analysis using µMAC-1000, is easy and friendly; the operator can run a sample only selecting a two keys analysis function on the integrated keyboard.

µMAC-1000 can perform very complex analytical cycles; the results are displayed in concentration units and provided through the analog or the RS-232 port.

Always ready for analysis  At the end of each analytical cycle the analyzer remain in stand by mode, without reagents consumption, always ready for next sample.

Easy to install
After the factory tests, the analyser is delivered ready to be installed; start-up kit is included; it is enough to prepare the reagents, to connect the sample line, the waste and the power to start the measurement.
Sample dilution  The analysis can be run either on the whole sample either after dilution on operator request. Dilution mode will be automatically activated on over range samples, with a dilution factor, factory selected, up to 100.

Features and benefits

  • Portable, easy to install and to manage;
  • Low reagents consumption; only few hundreds microliters of reagents per analysis, low reagents and disposable cost;
  • Fully automated operation; no operator attending required;
  • Automatic calibration; it is enough to select the calibration function to perform a new calibration;
  • Results data storage; the analyzer can store up to 400 measuring results including date, time and optical density.







Published in Portable Analyzers
Thursday, 01 April 2010 11:09

Easychem Pro

Direct reading Discrete Analyzer with 60 positions samples tray including blank, controls and calibrants cups.

  • Reaction tray with up to 80 temperature controlled and reusable reaction cuvette;.
  • Cooled reagents tray with capacity up to 18 reagents bottles;
  • Five steps washing station for reaction cuvettes;
  • Colorimetric detector with 9 position filter wheel for automatic wavelength selection;
  • STAT position option: sample addiction during analysis;
  • Pre or post run sample autodilution;
  • Samples throughput: 120/140 test per hour; 


Advantage and benefits

  • Easy to use: no specific experience or training required;
  • Flexibility: individual parameters list selectable on each sample, pre or post run sample autodilution, working standard autodilution from a stock standard;
  • Low reagents consumption: only a few microliters of reagents per analysis;
  • Low running costs: nearly no consumables, low reagents and disposable costs;
  • Immediate start up: no time waste or problems to reach hydraulic equilibrium;
  • Immediate shut down: no washing procedure required;
  • Windows based Software: easy to use and to learn; short training, specifically designed for chemists;
  • QC control: up to five level of real time QC can be used, QC results are automatically stored and plotted in a quality control chart;
  • QC actions: in case of QC out of tolerance the analyzer can stop the run or simply inform the operator leaving trace of malfunction storing the QC out of tolerance;
  • Data reprocessing: allows to check and reprocess the results file, including or deleting data treatment.